NO SOLICITING Vertical Door Plate in Solid Brass TO ORDER: Please add your preferences in the Notes to Seller section. (NOTE: ALL of the following information (1-3) is required when ordering. Any omission will result in a delay of your order.) (Charges for any other extras will be billed, via Paypal, in a separate invoice.) 1. Specify which fastening method you want:NOTE: Fasteners are NOT included except where specifically noted. See below for ordering fasteners of your choice. If you do not specify, you will receive 3/8″ brads with appropriate holes.No Holes with Tape (FREE) 1/16″ Holes with 3/8″ Brads (FREE) 3/32″ Holes with Short 1/4″ Phillips Head Screw ($1.95 EXTRA*) 3/32″ Holes with Long 3/8″ Phillips Head Screws ($1.95 EXTRA *) 2. Choose a font from our font chart photos: SIMPLE BLOCK (SB)SIMPLE BLOCK ITALIC (SBI)FOUR LINE BLOCK (FB)FOUR LINE BLOCK ITALIC (FBI)ROMAN BLOCK (RB)ROMAN BLOCK ITALIC (RBI)CLARENDON (C)CLARENDON ITALIC (CI)SIMPLE SCRIPT (SC)SLANT SCRIPT (SS)*CENTURY BLOCK (CB)OLDE ENGLISH (OE)NOTES:* (Charges for any other extras will be billed, via Paypal, in a separate invoice.)IMPORTANT: Check your eBay messages frequently. If we don’t receive a response from you to any questions we may have about your order before the eBay ship-by date, we reserve the right to make our best judgement as to layout, colors fonts, case, and/or size, in order to meet those shipping requirements.**************************************************************************************************** DESCRIPTION: These are the finest quality engraver’s plates in brushed solid brass .032″ (Almost a dime). One line of engraving is included, with no holes and heavy duty industrial double sided tape. LARGE SOLID BRASS PLATE – 3/4″ x 4 1/2″ with a .032 thickness, almost a dime, comes with choice of No Holes with Tape or 3/8″ brads, 1/4″ Phillips Head Screws ($1.95extra), or 3/8″ Phillips Head Screws ($1.95 extra) for mounting. For making a statement at your door elegantly. Solid brass with engraved message. If other than NO SOLICITING please send us a message, if you want other wording. (Extra charges may apply.) Plates are finished with a baked-on synthetic resin, that will not tarnish or rust. They are sturdy and thick enough to create an elegant finish for your door. We rotary diamond engrave the text 5 times into the brass, to create a very durable engraving, much more so than just diamond etching or laser engraving, that has a tendency to rub off. The exposed raw brass is then double acid oxidized to produce the darkened text. Please be double sure to check your order before submitting and include a phone number to reach you, if we have any questions. Please ask all questions before purchasing! INTERNATIONAL SHIPPING:We are NOT responsible for customs duty, taxes and fees, etc., or any delay that might be incurred from them. Thank you for your order. We have been in business since 1984, previously as Endless Creations, now as Endless Etc LLC, (endlessetc.com), with many satisfied and happy customers. We have attended many prestigious shows across the country, over the years, so whether you’re an ‘old’ customer, or a new client, we welcome you to experience our high standards of workmanship and service. We aim to please! Endless Etc Engraving
Read moreVTG Gold Brass Miniature Dollhouse Table Art Easel Faux Bamboo Display Stand 5 días ago
Dollhouse size brass easel, looks great! It is 2 1/4” tall x 1 1/8” wide x 1 5/8” deep.
Read moreVtg Gold MCM & Hollywood Regency Brass Faux Bamboo Tabletop Easel 8" 5 días ago
The free-standing easel features intricate details that add a touch of elegance to any tabletop or shelf, making it a unique and stylish addition to display small artwork, photos, or even books.
Read moreVintage brass faux bamboo easel Made in Italy 5 días ago
This vintage brass faux bamboo easel is a small decorative display easel made in Italy. It stands at a height of 5 inches, with dimensions of 3 inches in length and 3 inches in width. The elegant gold color and metal material give it a classic and sophisticated look, perfect for showcasing artwork, photos, or other items in your home decor. Its freestanding design makes it easy to place anywhere in your living space without the need for mounting.
Read moreVintage Faux Bamboo Brass Easel Stand Display Holder 6" Tall 5 días ago
Vintage Faux Bamboo Brass Easel Stand Display Holder 6″ Tall Easel is 7″ tall when not standing, 6″ when standing. Has some wear, please see photos for measurements and condition. Thank you.
Read moreDeltana DSW325U19 Wall Mount Solid Door Stop 2 1/2"X3 5/8h” Matte Black 5 días ago
Item is new. Never installed. See photos.
Read moreBiondan Brass VASE CAPRI WALL Mount H. 4 5/8" x W. 2 1/2" x 2 3/4" Made in Italy 5 días ago
VASE CAPRI WALL MT. H.4 5/8″x2 1/2″x2 3/4″.
Read moreNixie Tubes Clock on IN-12 Oak Vintage Wooden Case Temp. F/C 12/24H Slot Machine 5 días ago
IN-12 Nixie Tubes are one of the most beautiful, cheap and popular Nixie Tubes. Nixie Clock in Oak Wood Case. Clock support IN-12 Nixie Tubes (6 tubes [hh:mm:ss]). IN-12 Nixie Clock photos PCB design, chematic, casing and software made by GRA & AFCH.
Read moreKIT IN-14 Arduino Shield NCS314 Nixie Clock WITH TUBES FREE SHIPPING 5 días ago
DIY KIT IN-14 Arduino Shield Nixie Tubes Clock Shield for Arduino UNO/ MEGA NCS314 HW v2.2We provide FREE WORLDWIDE Economy shipping UPS Expedited delivery 3-5 days available DIY KIT for IN-14 Shield Nixie Clock with ColumnsDeveloped for 6 IN-14 xUSSR Nixie TubesIN-14 Tubes are one of the most popular mass-produced Nixie TubesNixie Clocks are one of the most beautiful and popular Vintage ClocksClock features Startup Tune, RGB backlight, USB port for updatesDIY KIT developed for Tubes Shield Board and Control Arduino BoardOptions include Tubes, Columns, Arduino and Power SupplyDIY KIT is made for Arduino UNO and MEGA 2560 Control BoardsIt allows you to write your own uniqe programs for the Arduino platformAll the latest Source codes are always available on our GitHub channelPCB, Design, Schematics, Case and Software made by GRA & AFCH Example of assembled Shield NCS314 Board: Listing includes:Tubes Shield (NCS314 v2.2) Bare PCBIN-14 Nixie Tubes – 6 pcsSet of Electronic Parts and Components for Shield (NCS314 v2.2) BoardSet of Screws and Spacers for Shield and Arduino BoardsPrincipal Electrical Scheme on paperBOM List for Shield (NCS314 v2.2) BoardUser Manual on a Vintage style paper The base listing contains only BARE PCB and full set of electronics partsWithout Arduino, Columns and Power SupplyListing includes bare PCB to make Shield NCS314 with soldered IN-14 Nixie Tubes This listing does NOT contain the Arduino board and power supply We are selling already flashed Arduino UNO here: (Uno) www.ebay.com/itm/162377278951Flashed Arduino Mega here: (Mega) www.ebay.com/itm/162377285626Power supplies: www.ebay.com/itm/162367596648Beautiful Acrylic Case ACNS314 v3.3 at a price of $ 34.95 www.ebay.com/itm/162736300779Glass Column: www.ebay.com/itm/162276387248GPS Receiver GA-6: https://www.ebay.com/itm/162682147400IR Remote Controller RM-X153: https://www.ebay.com/itm/162682141139 …And upload software into your arduino Link to (software) github.com/afch/NixeTubesShieldNCS314 Link to (video tutorial) Our Benefits: Easy to build beautiful clock – we offer housing Easy to customize firmware under Your own needs, thanks to an open platform – Arduino. Fast uploading via USB The latest version of the firmware always available on GitHub No need to download drivers – we are use only Genuine USB to serial converters. Drivers for them pre-installed in all popular OS: Windows, MacOS, Linux. Human friendly menu Very high qualty of Printed Circuit Boards Japan alluminium capacitors Power-On Self-Test Technical support Dear customers!If you have ANY questions, PLEASE ASK us Software Features: Shiled support 6 IN-14 Nixie tubes [hh:mm:ss] Full static display mode Slote Machine (Ani poisoning) Temperature display (DS18B20) [Celsius or Fahrenheit] GPS time synchronization (requires a standard GPS receiver, NMEA protocol, 5 volt power supply, not included) Operation via IR remote control (Remote control Sony RM-X151, not included) No need refresh or update information on the tubes The maximum possible brightness of the tubes 12/24 hour format. Date format: DD:MM:YY Unique RGB LEDs backlight with 16,7 million colors. Very easy to switch LEDS off/on. As alarm sound clock uses standard RTTTL (Nokia format) melodies, so You can easy change it. (included songs: mission impossible, we wish you). Easy updating firmware via USB using Arduino IDE. Power On Self-Test (POST): LEDs test, tubes test, sound test. Hardware Features: Integrated High Voltage Power supply: 150 – 220V. 3 PWM channels for RGB LEDs 8 bit per channel = 24bit = 16,7 million colors. It can be disabled in the menu (see manual). Test points for testing, adjusting and controlling low and high voltage circuits. Internal buzzer. RTC (Real Time Clock) High precision time chip DS3231 with Backup battery Acquiring time via external GPS module (only with Arduino Mega) 3 buttons on board to control Potenciometer to adjust High Voltage IR reciver TSOP4836 for IR remote controllers (may conflict with “Tone” library) Temperature sensor DS18B20 8 pcs of RGB SMD LEDs SPI up to 4Mhz Places for 2 column with 2 neon dots inside Separate controls upper and lower dots. Power consumption: 12V, 760mA. Recommended: 12V, 1-2A (center pin positive +) Reverse polarity protection Nixie Tubes Shiled NCS314 PCB size: 200mm x 53.34mm. (7.87 x 1.2 in) Shields comparison table: https://youtu.be/58xMATPCJ-I https://youtu.be/FMEhx8zmo_0 IN-14 Arduino Shield NCS314 v2.2 Electrical Scheme: Actual photos of the Shield NCS314 DIY KIT:Arduino Nixie Tubes Clock Shield NCS314 Top ViewArduino Nixie Tubes Clock Shield NCS314 bottom View Board dimensions in 2D and 3D Nixie Tubes Clock Shield for Arduino NCS314: This is example of assembled Shield Board NCS314 The base listing contains only BARE PCB and full set of electronics parts (Arduino, Columns and Power Supply are not included) User Manual Dear customers!If you have ANY questions, PLEASE ASK us Shipping and Return information All Items are shipped from UkraineVia International registered AirmailShipments are made within 1 business dayAfter the payments are received and verifiedIt takes about 4-7 days via UPS Express deliveryIt takes about 10-18 days via Standerd shippingIt takes about 35-45 days via Economy shippingWe combine multiple Items to save on shipping UPS Express Shipping time (recommended):Europe:3-5 daysGermany:3-5 daysUSA, Canada:4-7 daysAsia, South America:5-7 daysAustralia, New Zeland:5-7 daysAfrica, Central America:5-7 days Standard Shipping time:Europe:10-12 daysGermany:10-12 daysUSA, Canada:10-15 daysAsia, South America:10-18 daysAustralia, New Zeland:12-18 daysAfrica, Central America:12-18 days Economy Shipping time:Europe:25-30 daysGermany:25-30 daysUSA, Canada:30-35 daysAsia, South America:35-45 daysAustralia, New Zeland:45-55 daysAfrica, Central America:45-55 days Return PolicyAll Returns are acceptedFor Return you should contact Us within 14 Days after receiving the ItemRefunds are made as Money back or Replacements (buyer’s choice)Return Shipments are paid by the buyerNo restocking fees are charged
Read moreDIY KIT Nixie Tubes Clock IN-12 Arduino Shield NCS312 [WITH OPTIONS] 12/24H GPS 5 días ago
DIY KIT IN-12 Arduino Shield Nixie Tubes Clock Shield for Arduino UNO or MEGA – NCS312 UPS Express delivery is highly recommended Economy Shipping very slow and unreliable The Ardrduino Nixie Tubes Shiled NCS312 allow You to make 6 digits Nixie Tubes Clock in “Divergence Meter Mini” style (by GRA & AFCH). Or You can just display any 6 digits strings on this IN-12 Nixie Tubes made in xUSSR. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. PCB design, schematic, housing and software made by GRA & AFCH. Nixie Clock Shield NCS312 compatible with Arduino UNO/Genuino & Arduino MEGA, so it allows you to write your own unique programs on the Arduino platform, the latest sources are always available on github at the «NixeTubesShieldNCS314» repository Listing includes:Bare NCS312 Shield Board IN-12 Nixie Tubes – 6pcs (optional, choose in selector)NE2H-1 Neon Lamps for Dots – 4 pcsArduino Control Board (optional, UNO or MEGA)GPS Receiver – (optional, choose in selector)IR Remote – (optional, choose in selector)Set of Socket pins for 6 IN-12 Nixie Tubes (72 pcs)Set of electronics partsSet of hex spacers and screwsClear Acrylic Stand for NCS312 ShieldPower supply (12V/1A) (optional AC plug US EU UK AU)BOM List of CompnentsPrincipal Electrical SchemeUser Manual on vintage-style paper Base Listing contains Shield NCS312 with IN-12 Nixie Tubes and NE2H Neon LampsOptional part can be purchase separately by links below We are selling already flashed Arduino UNO here: (Uno) www.ebay.com/itm/162377278951Flashed Arduino Mega here: (Mega) www.ebay.com/itm/162377285626Power supplies: www.ebay.com/itm/162367596648GPS Receiver GA-6: https://www.ebay.com/itm/162682147400IR Remote Controller RM-X153: https://www.ebay.com/itm/162682141139 …And upload software into your arduino Link to (software) github.com/afch/NixeTubesShieldNCS314 Link to (video tutorial) link was hidden by eBay Our Benefits: Easy to build beautiful clock – we offer housing Easy to customize firmware under Your own needs, thanks to an open platform – Arduino. Fast uploading via USB The latest version of the firmware always available on GitHub No need to download drivers – we are use only Genuine USB to serial converters. Drivers for them pre-installed in all popular OS: Windows, MacOS, Linux. Human friendly menu Very high qualty of Printed Circuit Boards Japan alluminium capacitors Power-On Self-Test Technical support Dear customers!If you have ANY questions, (PLEASE ASK us). Software Features: Shiled support 6 IN-12 Nixie tubes [hh:mm:ss] Full static display mode Slote Machine (Ani poisoning) Temperature display (DS18B20) [Celsius or Fahrenheit] GPS time synchronization (requires a standard GPS receiver, NMEA protocol, 5 volt power supply, not included) Operation via IR remote control (Remote control Sony RM-X151, not included) No need refresh or update information on the tubes The maximum possible brightness of the tubes 12/24 hour format. Date format: DD:MM:YY Unique RGB LEDs backlight with 16,7 million colors. Very easy to switch LEDS off/on. As alarm sound clock uses standard RTTTL (Nokia format) melodies, so You can easy change it. (included songs: mission impossible, we wish you). Easy updating firmware via USB using Arduino IDE. Power On Self-Test (POST): LEDs test, tubes test, sound test. Hardware Features: Integrated High Voltage Power supply: 150 – 220V. 3 PWM channels for RGB LEDs 8 bit per channel = 24bit = 16,7 million colors. It can be disabled in the menu (see manual). Test points for testing, adjusting and controlling low and high voltage circuits. Internal buzzer. RTC (Real Time Clock) High precision time chip DS3231 with Backup battery Acquiring time via external GPS module (only with Arduino Mega) 3 buttons on board to control Potenciometer to adjust High Voltage IR reciver TSOP4836 for IR remote controllers (may conflict with “Tone” library) Temperature sensor DS18B20 8 pcs of RGB SMD LEDs SPI up to 4Mhz Places for 2 column with 2 neon dots inside Separate controls upper and lower dots. Power consumption: 12V, 760mA. Recommended: 12V, 1-2A (center pin positive +) Reverse polarity protection Nixie Tubes Shiled NCS314 PCB size: 200mm x 53.34mm. (7.87 x 1.2 in) IN-12 Arduino Shield Nixie Tubes Clock on Acrylic Stand Boards Dimensions in 2D and 3D Nixie Tubes Clock Shiled for Arduino NCS312: User Manual Dear customers!If you have ANY questions, PLEASE ASK us Shipping and Return information All Items are shipped from UkraineVia International registered AirmailShipments are made within 1 business dayAfter the payments are received and verifiedIt takes about 4-7 days via UPS Express deliveryIt takes about 10-18 days via Standerd shippingIt takes about 35-45 days via Economy shippingWe combine multiple Items to save on shipping UPS Express Shipping time (recommended):Europe:3-5 daysGermany:3-5 daysUSA, Canada:4-7 daysAsia, South America:5-7 daysAustralia, New Zeland:5-7 daysAfrica, Central America:5-7 days Standard Shipping time:Europe:10-12 daysGermany:10-12 daysUSA, Canada:10-15 daysAsia, South America:10-18 daysAustralia, New Zeland:12-18 daysAfrica, Central America:12-18 days Economy Shipping time:Europe:25-30 daysGermany:25-30 daysUSA, Canada:30-35 daysAsia, South America:35-45 daysAustralia, New Zeland:45-55 daysAfrica, Central America:45-55 days Return PolicyAll Returns are acceptedFor Return you should contact Us within 14 Days after receiving the ItemRefunds are made as Money back or Replacements (buyer’s choice)Return Shipments are paid by the buyerNo restocking fees are charged
Read more